How does the shaker agitation rate and orbit affect culture growth?

Generally, agitation speed and orbit affect both the aeration and the mixing of the culture. Greater aeration increases oxygen transfer rate (OTR), boosting cell growth. The size of the orbit affects OTR linearly and the speed has a square-law relationship. Therefore, if the size of the orbit doubles, say from 1/2 to 1," the amount of OTR should double〖RPM〗_1/〖RPM〗_2 = (r_2^2)/(r_1^2 ), then 〖RPM〗_2 = √(〖RPM〗_1^2 (r_1/r_2 ) ). If the speed doubles, the OTR should quadruple. Of course, these are general rules and caution should be taken with shear sensitive cells. However, this information can be used to estimate the conditions needed to obtain the same results on different model shakers. For example, to get the same oxygen transfer in a shaker with a 1 in orbit running at 300 rpm, a shaker with 3/4 in orbit must be run at 350 rpm.

Do Eppendorf shakers come with platforms?

Each Eppendorf shaker is available with multiple platform options, which are ordered separately to give you the flexibility to choose the one that best suits your needs. Dedicated platforms include installed clamps of a single size (ie. only 250 mL clamps) and provide in most cases the best capacity but does not allow for the use of different size clamps or holders. Universal Platforms are designed for use with a combination of various-sized clamps and test tube racks providing maximum flexibility. When ordering a Universal Platform, clamps and test tube racks must also be ordered separately.

What is the temperature offset function?

The temperature offset function on many of our shakers allow you to match a reference point" temperature inside the chamber (culture medium) with the "Actual Value" displayed. The temperature offset function on Innova Incubated shakers allows you to monitor the temperature of the media providing you a clearer and more accurate picture. Please be aware that matching reference point temperatures to the Actual means you have to deal with many variables such as: greater evaporation; heat gains generated by cultures growing - (slowly at first and much more during their growth phase) and heat generated by the friction of media with the glass at high speeds or use of baffled flasks. Over time, the reference point temperature offset may need to change due to these varying conditions.

I want to grow my cultures at 27°C, do I need an incubated shaker with refrigeration?

The Eppendorf Incubated, non-refrigerated Shakers Innova and I-Series are designed to maintain temperatures of ambient plus 5 °C to its maximum operating temperature. The Eppendorf Incubated Excella shakers will operate from ambient plus 7 °C to maximum temperature. It is critical to understand that "ambient temperature is not the temperature on the wall thermometer (room temperature), but the temperature measured one meter from the front of the machine.

Why are some flask clamps supplied with an extra spring set?

This "extra spring set" (we call it a girdle) is included with clamps for 2 L, 2.8 L, 4 L and 6 L flasks. It is intended to be used with the already installed spring set. This girdle helps prevent large flasks from spinning inside the clamp and reduces the risk of flasks becoming dislodged or scored by the steel clamp. One girdle is already in place on the clamp, the other is packed separately. To install this extra “girdle”, follow the instructions in the manual supplied with the shaker.

How is temperature accuracy defined by Eppendorf?

Accuracy is defined as the degree of closeness between the displayed value and the actual value as determined by a traceable device. All Eppendorf Incubated Innova and I-Series shakers have a temperature Accuracy of ±0.1 °C from 30 – 40 °C, ±0.5 °C over the remaining range. New Brunswick Incubated Excella Shakers are accurate within 0.1°C at 37°C.

How is Uniformity defined by Eppendorf?

Uniformity is the ability to maintain uniform temepratures throughout the platform. New Brunswick Incubated Innova Shaker temperatures will not deviate by more than +/- 0.25 °C at 37 °C.

The orbit of a shaker is the distance traveled around the central drive. This can be descibed in inches, centimeters, or milimeters. If our shakers had a one inch (2.54 cm) orbit. That means that that the lateral movement of the platform would equal one inch from one point to another that is 180° opposite that position. All of the New Brunswick. shakers have a circular orbit

Which screws will fit to which platform ?

All of Eppendorf Inc. clamps and accessories are packaged with multiple screws to fix them to our universal platforms, included in M1013-0261 clamp screw kit (Stainless steel platform screw #S2117-3050 (10-32 x 5/16 in (7.9mm)), Stainless Steel, Aluminum, and Aluminum and Phenolic (Plastic) #S2116-3051 (10-24 x 5/16 in (7.9 mm)), and Wood #S2116-3101 (10-24 x 5/8 in (15.87mm)).

How can I disinfect, clean, maintain my shaker?

We recommend cleaning the exterior of our units with a damp cloth or any standard household or laboratory cleaner to wipe the surfaces clean. Do not use abrasive or corrosive compounds to clean the instruments as they may damage the unit and void the warranty. It is the responsibility of theuser to carry out the proper decontamination procedures if hazardous materials are spilled on or inside the equipment. Before using any cleaning or decontamination method other than those suggested by the manufacturer, users should contact Eppendorf Inc. to ensure that the proposed method will not damage the equipment. Commercially available household bleach solutions, when diluted at a 1:10 ratio, are effective in routine decontamination of the instrument. The method for decontaminating a spill depends on the nature of the spill. Spills involving fresh cultures or samples of known concentrations of biomass should be flooded with decontamination solution and soaked for at least 5 minutes before cleanup. Spills involving samples with high concentrations of biomass, or involving organic matter, or occuring in areeas warmer than ambient/room temperature, should be exposed to decontamination solution for at least one hour before being cleaned up. Personnel involved in the cleanup of any spill should wear gloves, safety glasses, and a laboratory coat or gown during the cleanup process. Respiratory protection should be considered for spills where aerosolization is suspected.

Which flask type fits in which clamp ?

Please see the Accessories for New Brunswick™ Shakers: Dimensions and Capacities in the Userguides section of the shaker product page.

Which vessel fits in Eppendorf Test tube racks ?

Please see the Accessories for New Brunswick™ Shakers: Dimensions and Capacities in the Userguides section of the shaker product page.

What is the humidity option ? Is the value of humidity shown in the display ? How can I avoid evaporation?

The humidity monitoring option that is offered with our Innova line displays the Relative Humidity (RH) of the chamber. This value will be reported if the shaker is equiped with the humidity sensor. The value can be shown in the main display screen if programmed to do so or the value can be viewed with all other parameters under the SUMM (summary) screen.The calibrated sensor is accurate within 3 % up to 95 % RH and 5 % up to 99 % RH. To avaoid evaporation in the shakers, it is recommended to fill the humidification resevoir beneath the platform, this will mitigate loss of culture volume.

Why is the triple eccentric drive special ? What is the difference between Innova and Excella Shakers drive ?

The Innova and I-series Triple eccentric drive consists of three individual bearings and eccentric shafts mounted in a triangular fashion for precise uniform circular motion at every point on the platform. The heavy duty drive has a single shaft that utilizes springs to aid in balancing the load. This drive works great with small to medium loads at lower speeds.

How can I shake MTPs ? Which parameters ?

Eppendorf shakers offer a variety of Micro Titer Plate holders that attach to our univeral platforms. Our shakers offer a variety of orbits up to 5.1 cm (2 in) and speeds up to 500 rpm. If mixing is what is needed at higher speeds and smaller orbits you can find Eppendorf Mixers.

How do I use of sticky pads/sticky tape?

Eppendorf Sticky Pads are recommended for use on our sticky pad platform or our sticky pad adapter kit (M1250-9504). On the S44i universal platform sticky pad can be used directly. The adapter kit is easily fixed to our universal platforms. Any size flask can be used with the sticky pad with a 1 in (2.54 cm) orbit up to 250 rpm, any size flask can be used with the 2 in (5.1 cm) orbit up to 200 rpm. To clean the sticky pad, just wash with soap and water. this will revive" the stickiness, but the sticky pad must be completely dry before replacing on the platform.

What is the heavy load platform ?

The Heavy Duty Platform (M1282-9928) is designed for use in the Innova 44 only. This platform is 0.95 cm thick alluminum plate that is recommended for shaking full loads of flasks greater than 1 L at or above 20 % fill volumes or flasks with baffles.

What is the orbit of a shaker?

An orbital shaker moves the platform in a circular shaking motion. The term orbit describes the diameter of this circular movement. Typical orbit sizes are 1.9 cm, 2.5 and 5 cm.

What orbit shall I take?

An orbital shaker is used to grow microorganisms or cells growing in suspension, like bacteria, yeast, fungal, insect, algae or plant cells. Orbital shaking enables a homogeneous distribution and aeration of the cultures by increasing the oxygen transfer rate (OTR). There are different influencing parameters on shaking performance, e.g. the shaker orbit, the applied speed, the vessel shape, the liquid viscosity and the filling volume. The 2.5 mm orbit is the standard solution which works well for most applications. For some applications, e.g. large vessels > 2 Liter, especially large volume Fernbach flasks or very shear sensitive cells, a larger shaking diameter with the consequence of a reduced speed can be beneficial.

What platform types are offered with the shakers?

Universal platform and a variety of dedicated platforms are available. University platforms offer maximum flexibility having a hole-pattern that allows using virtually any combination of clamps and other accessories. Dedicated platforms come complete with pre-installed clamps of one size. The hole-pattern of the dedicated platform is optimized for the use of one specific size of clamps. It allows in most cased more capacity but can only be used with that size of clamp. Please note that the platform has to be ordered in addition to the shaker.

I use two shakers with different orbits. Can I transfer my experimental conditions to a shaker with a different orbit?

Yes, the rpm can be adapted with help of the following formula .

How much are the different orbital shaker service programs?

The cost depends on the product variant and on the level of service that is required. Please contact your local Eppendorf Service centre for a personal quotation. www.eppendorf.com/contact

Why should I have my Orbital Shaker serviced at regular intervals?

As with all products with moving parts, wear and tear is inevitable and can affect how consistently the product operates over a long period of time. Eppendorf products are engineered to minimize wear and tear, but a periodic service allows early identification and tracking of excessive wear before product performance is outside of acceptable tolerances. Regular servicing may also be a regulatory requirement of our users.

What is IQ or OQ and what do I need them for?

Installation and Operational Qualification; the Installation Qualification documents that the product has been delivered and installed in accordance with manufacturer recommendations and guidelines. The Operational Qualification checks the correct functioning of a device in accordance with manufacturer recommendations and guidelines (as such, it can only be provided by the equipment manufacturer). IQ/OQ is primarily required in organizations that implement quality management processes but is available to all users.

How often does my orbital shaker need to be serviced?

Eppendorf recommends a service once every 12 months. However, the regulatory requirements of our users vary greatly and can often be more frequent.

text.skipToContent text.skipToNavigation

JP | JPY

結果がありません

検索の提案

製品群

Show all Product Families ()

商品番号

Show all Articles ()

コンテンツ

Show all Content ()

New Brunswick Innova^® 40/40R - 卓上型旋回シェーカー

製品情報

可視性に優れ、すぐにフラスコの出し入れができ、最大3 Lの容量まで扱えるコンパクトな卓上型旋回シェーカーはいかがですか? Innova 40/40Rは有名なInnovaトリプルエキセントリックドライブ備え、プログラムが容易な旋回シェーカーであり、年中休まず使用しても長年にわたり安定して使用できます。

製品情報をもっと見る

Click to customize and configure your universal platform accessories

デモの依頼

追加でダウンロードできる材料がありますこのページの最後に

製品 (4)

Services (14)

アクセサリー (17)

VisioNize (1)

4 製品

New Brunswick Innova^® 40

積み重ね不可, 100 V/50/60 Hz (US), 軌道 1.9 cm（0.75 インチ）

製品のさらなる情報

数量

在庫確認してください

カタログ番号 M1299-0083

希望小売価格

¥ 1,460,000

税込価格

¥ 1,606,000

お問い合わせ

New Brunswick Innova^® 40R

冷蔵式, 積み重ね不可, 100 V/50/60 Hz (US), 軌道 1.9 cm（0.75 インチ）

製品のさらなる情報

数量

在庫確認してください

カタログ番号 M1299-0087

希望小売価格

¥ 1,720,000

税込価格

¥ 1,892,000

お問い合わせ

New Brunswick Innova^® 40

積み重ね不可, 100 V/50/60 Hz (US), 軌道 2.5 cm（1 インチ）

製品のさらなる情報

数量

在庫確認してください

カタログ番号 M1299-0093

希望小売価格

¥ 1,460,000

税込価格

¥ 1,606,000

お問い合わせ

New Brunswick Innova^® 40R

冷蔵式, 積み重ね不可, 100 V/50/60 Hz (US), 軌道 2.5 cm（1 インチ）

製品のさらなる情報

数量

在庫確認してください

カタログ番号 M1299-0097

希望小売価格

¥ 1,720,000

税込価格

¥ 1,892,000

お問い合わせ

製品をもっと見せる

お客様のショッピングカートに追加されました。

製品情報

テクニカルデータ

アプリケーション

特徴

Innova40と40Rの(冷蔵)による卓上シェーカーは長年の頼り甲斐ある運転をご提供します。これは、ボリュームまたはスループットを向上させる目的で小規模プロジェクトで作業を開始するのに最適なシェーカーです。自立型の透明なリッドにより、サンプルを常に見ることができます。このようなコンパクトなベンチトップユニットで最大3 Lのフラスコを振ることができるため、アップスケールの明確な範囲を提供し、オプションにはドリップパンとリモートアラームが含まれます。シンプルなユーザーインターフェイスにより、速度、温度、時間を簡単にプログラミングできます。 VisioNizeボックスを追加して監視を強化し、通知機能を追加できます。定期的な修理は現場で実施できるため、ダウンタイムを最小限に抑えることができます。

VisioNize^® Lab Suiteを使って効率的なラボと装置管理

ラボ装置の監視や通知の受信（装置アラームのためなど）に関心がありますか？デジタル接続されたラボは、さらに多くの事を提供します。

モジュール式バンドルソフトウェアサービスにアクセスし、ラボに適したものを選択します。VisioNize Lab Suiteは、お客様がラボ管理者や科学者として、試料のセキュリティ、コンプライアンスのニーズ、メンテナンス管理のためのラボのデジタル管理を開始するために必要なものすべてを提供します。

デジタルラボの卓越性を実現するための独自のコースを作成しましょう！詳細

読む量をもっと少なくする

仕様	Innova^® 40R, 軌道直径1.9 cm (3/4 in)	Innova^® 40, 軌道直径2.5 cm (1 in)	Innova^® 40R, 軌道直径2.5 cm (1 in)	Innova^® 40、軌道直径1.9 cm (3/4 in)

外部の高さ（蓋/ドアが開いている状態）	101.6 cm（40 インチ）	101.6 cm（40 インチ）	101.6 cm（40 インチ）	101.6 cm（40 インチ）
タイマー	0.01 – 99.59 時間、連続	0.01 – 99.59 時間、連続	0.01 – 99.59 時間、連続	0.01 – 99.59 時間、連続
電源	100 V, 50/60 Hz	100 V, 50/60 Hz	100 V, 50/60 Hz	100 V, 50/60 Hz
寸法（W × D × H）	55.9 × 76.2 × 61 cm / 22 × 30 × 24 in	55.9 × 76.2 × 61 cm / 22 × 30 × 24 in	55.9 × 76.2 × 61 cm / 22 × 30 × 24 in	55.9 × 76.2 × 61 cm / 22 × 30 × 24 in
製品の重量	79.4 kg / 175 lb	60.3 kg / 133 lb	79.4 kg / 175 lb	60.3 kg / 133 lb
温度範囲	周囲温度-15℃～80℃（最低4℃）4 ℃)	周囲温度 + 10 ℃ ～ 80 ℃	周囲温度 - 15 ℃から80 ℃（最小 4 ℃）	周囲温度 + 10 ℃ ～ 80 ℃
可聴アラームと視覚アラーム	はい	はい	はい	はい
温度の均一性	±0.25 °C ＠ 37 °C	±0.25 °C ＠ 37 °C	±0.25 °C ＠ 37 °C	±0.25 °C ＠ 37 °C
利用可能なプログラムモード	• 定速と定温 • プログラム可能マルチステップ • RS-232通信ポート	• 定速と定温 • プログラム可能マルチステップ • RS-232通信ポート	• 定速と定温 • プログラム可能マルチステップ • RS-232通信ポート	• 定速と定温 • プログラム可能マルチステップ • RS-232通信ポート
ドライブ機構	トリプル偏心カウンターバランスドライブ	トリプル偏心カウンターバランスドライブ	トリプル偏心カウンターバランスドライブ	トリプル偏心カウンターバランスドライブ
ベンチトップ(B)、アンダーベンチ(U、フロア(F) 、スタック式 (S)	B	B	B	B
メモリー	停電時の自動再起動による不揮発性	停電時の自動再起動による不揮発性	停電時の自動再起動による不揮発性	停電時の自動再起動による不揮発性
モータータイプ	ソリッドステート、DCブラシレスモーター	ソリッドステート、DCブラシレスモーター	ソリッドステート、DCブラシレスモーター	ソリッドステート、DCブラシレスモーター
プラットフォームサイズ	46 × 46 cm（18 × 18 インチ）	46 × 46 cm（18 × 18 インチ）	46 × 46 cm（18 × 18 インチ）	46 × 46 cm（18 × 18 インチ）
冷蔵式	はい	−	はい	−
スライドアウトプラットフォーム	いいえ	いいえ	いいえ	いいえ
ドアオープニング	トップオープニングフード	トップオープニングフード	トップオープニングフード	トップオープニングフード
速度範囲	25 ~ 500 rpm (負荷に応じて)	25 ~ 500 rpm (負荷に応じて)	25 ~ 500 rpm (負荷に応じて)	25 ~ 500 rpm (負荷に応じて)
マルチステッププログラミング	はい	はい	はい	はい
プログラムごとのステップ	15	15	15	15
ストアド・プログラム	4	4	4	4
cETLusとCEマーク付き	はい	はい	はい	はい
容量	中	中	中	中
プログラミングステップ / 保存可能なプログラム	15/4	15/4	15/4	15/4
リモート装置監視および通知 (VisioNize^®)	VisioNize^®ボックス可能	VisioNize^®ボックス可能	VisioNize^®ボックス可能	VisioNize^®ボックス可能
温度範囲	常温以下15 °Cから80 °C（最小 4 °C)	常温以上10 °Cから80 °C	常温以下15 °Cから80 °C（最小 4 °C)	常温以上10 °Cから80 °C

撹拌
軌道	1.9 cm（0.75 インチ）	2.5 cm（1 インチ）	2.5 cm（1 インチ）	1.9 cm（0.75 インチ）